If your Morphy Richards iron is sticking to clothes, dragging across fabric or leaving scorch marks, the most common causes are a temperature setting that is too high for the garment, fabric residue on the soleplate or ironing over heat-sensitive materials.
Sticking does not necessarily indicate a fault with your iron. The checks below will help you identify the cause and get back to smoother ironing.
Why is my iron sticking to fabric?
The temperature is too high for the garment
Different fabrics tolerate different levels of heat. A setting suitable for cotton or linen may be too hot for delicate or synthetic materials, causing them to scorch, melt or stick to the soleplate.
Always check the garment’s care label before ironing. For mixed-fibre fabrics, follow the care label and use a setting suitable for the most heat-sensitive fibre.
Do not iron garments marked with a crossed-out iron symbol.
There is residue on the soleplate
The soleplate is the flat surface underneath your iron. A build-up of starch, laundry-product residue or melted fibres can make this surface sticky and may transfer marks onto other garments.
Check the soleplate once the iron is unplugged and completely cool. Any visible deposits should be cleaned using the method recommended in your user manual.
You are ironing over prints or embellishments
Printed designs, transfers, sequins and other decorative finishes may stick or become damaged when they come into direct contact with a hot soleplate.
Follow the garment’s care instructions. Where ironing is permitted, the label may recommend ironing on the reverse or using a pressing cloth.
The iron is resting on the fabric for too long
Holding a hot iron in one place can scorch fabric, even when the temperature setting is otherwise suitable.
Keep the iron moving during use and place it in the resting position specified in your user manual when pausing to adjust a garment.
What should I do if my iron starts sticking?
- Stop ironing the garment. Continuing may damage the fabric or spread residue onto other clothes.
- Switch off and unplug the iron, then allow it to cool completely.
- Check the garment’s care label against the temperature setting you were using.
- Inspect the cool soleplate for residue, stuck fibres or visible damage.
- Clean the soleplate as instructed in your user manual before using the iron again.
If your iron has an adjustable temperature, allow it time to cool after changing from a higher setting to a lower one. Turning the dial down does not immediately reduce the soleplate temperature.
If your model uses an automatic temperature setting, follow its user manual for suitable fabrics and operating instructions.
How do I clean a sticky iron soleplate?
For light surface residue:
- Unplug the iron and allow it to cool completely.
- Gently wipe the soleplate with a soft, damp cloth.
- Dry it with a soft cloth.
Do not scrape the soleplate, pull off firmly bonded material or use metal pads, sharp objects or abrasive cleaners. These can damage the surface.
For burnt-on fabric or stubborn deposits, follow the specific cleaning instructions for your model. Do not use vinegar, descaler or other cleaning products unless your user manual specifically recommends them for the soleplate.
You can find your model’s cleaning guidance in your Morphy Richards user manual.
How can I prevent my iron from sticking?
- Check the care label every time, particularly when switching between different fabrics.
- Start with garments requiring a lower temperature, then work up to those suitable for higher heat.
- Allow the iron to cool when reducing the temperature.
- Test a small, hidden area first, provided the garment’s care label permits ironing.
- Use a clean pressing cloth where recommended by the garment’s care instructions.
- Avoid direct contact with prints, transfers and embellishments.
- Keep the soleplate clean and check for residue before ironing.
- Keep the iron moving rather than leaving it resting on fabric.
Getting the best results from your iron
Always follow the garment manufacturer’s care label for ironing guidance and your iron’s user manual for operating and cleaning instructions.
If residue remains after wiping the cooled soleplate, check your model’s manual for the recommended method of removing stubborn deposits. Avoid experimenting with cleaning products or household remedies, as these may damage the soleplate.
You can find the care instructions for your model in your Morphy Richards user manual.