This guide covers the Morphy Richards Speed Steam Steam Generator Iron (model 333202 and 333201). Find out what water to use, how to run Self Clean and what to check if your iron won’t heat, stops steaming or leaves marks on clothes.
Check the model number on the appliance’s rating label once it’s unplugged and cool. The 333202 and 333201 uses a Self Clean cycle that you start manually and drain into a sink. Use the steps below only if your model number is 333201 or 333202.
Start here: what is your Speed Steam doing?
| What you notice | What to do first |
|---|---|
| The power light won’t come on | Check that the plug is fully inserted, the wall socket is switched on and you’ve pressed On/Off on the base. |
| The base has power but the iron won’t heat | Check that the temperature dial isn’t set to MIN. Give the iron time to heat up. |
| There’s little or no steam | Check the water level, temperature setting and steam light. If the Descale button is lit, run Self Clean. |
| Steam keeps coming after you release the trigger | A little steam for a few seconds is normal. If it continues, press the trigger once to turn off steam boost. |
| The appliance beeps and switches off after 10 minutes without use | Auto shut-off has activated. Press On/Off and let the iron heat again. |
| The Descale button lights up and the appliance beeps at switch-on | Self Clean is due. Unplug the appliance and let it cool for at least two hours before following the Self Clean steps. |
| The Descale button flashes during Self Clean | The cycle is running. Keep clear of the hot water and steam draining into the sink. |
| Clear droplets come from the soleplate | Let the iron heat fully. Use a temperature suitable for steam and reduce the steam level if needed. |
| Brown water comes from the soleplate or the iron leaves marks | Stop ironing the garment. Once the iron is cool, check the soleplate for residue and check what water you’ve been using. |
| Water leaks from the tank, base or hose, or the appliance trips the electrics, sparks, smokes or smells burnt | Stop using it. Switch off and unplug it if safe, then contact Customer Support. Don’t switch it back on to test it. |
What water should I use in my Speed Steam 333201 333202?
We recommend distilled, deionised or demineralised water to help reduce limescale, especially if you live in a hard water area. Don’t use scented ironing water or add vinegar, chemical descaler, starch or other additives.
- Switch off and unplug the steam generator before filling.
- Squeeze the tank release button and slide out the detachable tank.
- Fill through the opening up to the MAX line.
- Slide the tank back into the base and make sure it’s secure.
If the water level gets too low, the steam generator stops producing steam. Refill and refit the tank before continuing.
How do I use the temperature and steam settings?
- Place the base on a firm, level, heat-resistant surface. Before first use, remove any protective covers and straighten the power lead and steam hose. Try your first pass on an old towel.
- Slide the iron lock to the unlocked padlock position and lift the iron off the base. Plug in the appliance and press On/Off.
- Set the temperature dial on the iron to suit the garment’s care label. Use the steam level button on the base to select the steam output. Use dry ironing for fabrics that need a low temperature without steam.
- Wait for the temperature light on the iron to go out and the selected steam light on the base to stop flashing.
- Press and hold the steam trigger for normal steam. A short delay is normal while steam travels from the base to the iron.
Steam boost: Press the steam trigger twice quickly to start boost. Press it once more to turn boost off. A little steam may continue for a few seconds after you release the trigger. If steam keeps coming after you’ve turned boost off, switch off and unplug the appliance if safe, then contact Customer Support.
Dry ironing: You don’t need to fill the tank or select a steam level. Set the temperature to suit the garment and iron without using steam.
Vertical steaming: If the care label allows steam, hold the iron about 1–2 cm from the hanging fabric. Press the trigger twice quickly for boost and once to turn it off. Never steam clothes while someone is wearing them.
Why won’t my Speed Steam switch on, heat up or stay on?
- The power light is off: Check the plug, wall socket switch and On/Off button on the base. If there are no signs of damage and the electrics haven’t tripped, check whether another appliance works in the socket. If the socket works but the steam generator still has no power, contact Customer Support.
- The base has power but the iron isn’t heating: Check that the dial isn’t set to MIN. Select a temperature that suits the garment and give the iron a minute or two to warm up and settle. The temperature light goes out when it reaches the selected setting. Don’t touch the soleplate to check it.
- The iron seems too hot or not hot enough: Check the dial against the garment’s care label. If you’ve turned the temperature down, wait for the iron to cool to the new setting before continuing. If it repeatedly scorches fabric at the correct setting or still won’t heat properly, stop using it and contact us.
- It beeped and switched off after a pause: The Speed Steam 333202 automatically switches off after 10 minutes without use. Press On/Off and allow it to heat again. If it repeatedly switches off while you’re actively using steam, tell us when it stops and which lights or beeps you notice.
Why is my Speed Steam producing little or no steam?
- Check the tank. Make sure it contains enough water and is securely fitted. If the pump suddenly sounds louder or steam fades, check whether the water has run low.
- Check the temperature. Select a setting suitable for steam and permitted by the garment’s care label. Wait for the temperature light on the iron to go out.
- Check the steam light. Wait until the selected steam light on the base stays steady. If auto shut-off activated, press On/Off and allow the appliance to heat again.
- Hold the steam trigger. Allow a short delay for steam to reach the iron. An occasional pumping sound is normal while the appliance draws water from the tank.
- Check the Descale button. If it’s lit, follow the Self Clean steps below.
If steam is still weak, intermittent or absent, contact Customer Support. Tell us whether it never started or worked at first and then stopped.
How do I descale my Speed Steam 333201, 333202?
When the Descale button lights up, the boiler needs cleaning. The appliance beeps at switch-on as a reminder until Self Clean is completed. You’ll need the supplied boiler drain tube and its connector to run the cycle.
Prepare the appliance
- Unplug the steam generator and leave it to cool for at least two hours. Make sure it’s completely cold before proceeding. Never remove the boiler screw while the appliance is hot.
- Lock the iron securely onto the base. Remove the water tank to prevent spills, then turn the cooled steam generator over to locate the boiler screw underneath.
- Unscrew the boiler screw anticlockwise. Take the drain tube and connector out of their storage position. Push the connector firmly into the opening and lay the tube in its groove.
- Return the appliance upright. Fill and refit the water tank. Use clean water without descaling chemicals.
- Position the front of the base securely over a sink so the tube hangs down into the sink. Make sure the tube isn’t pinched between the base and the edge of the sink.
Run Self Clean
- Plug in the appliance and press On/Off. Straight away, hold the Descale button and steam trigger together for one to two seconds, then release. A beep and a flashing Descale button confirm the cycle has started.
- Keep clear of the tube while hot water and steam drain into the sink. Don’t touch the tube or move the appliance during the cycle.
- After about two minutes, you’ll hear a long beep. The Descale light goes out and the appliance switches itself off.
- Unplug the appliance and let it cool completely. Remove the tube and connector and return them to storage. Refit the boiler screw clockwise and tighten it fully before using the appliance again.
If the drain tube or connector is missing, or the boiler screw won’t refit securely, contact Customer Support. Don’t improvise a replacement or run Self Clean without the supplied tube.
Why won’t Self Clean start, or why is the Descale light still on?
- Check that the Descale button is lit. Self Clean can only be started when the appliance is asking for it.
- Check that the boiler is cold. If the appliance is still warm or you waited too long after switching on, unplug it and let it cool completely before trying again.
- Check the water tank and button timing. Make sure the tank has enough water and is securely fitted. Once the drain tube is set up, press both controls together immediately after switching on. Hold them for no more than two seconds.
If the cycle still won’t start or finish, contact Customer Support. Tell us whether the Descale button flashed, whether water drained into the sink and whether you heard the long beep.
Why is my iron dripping clear water?
A few drops from the steam holes in the soleplate can occur if the iron is too cool for the steam setting or the base moves while you’re ironing.
- Wait for the iron to heat fully, including after auto shut-off.
- Make sure the temperature setting allows steam. At lower temperatures that still allow steam, choose a lower steam level.
- Use shorter bursts of steam and keep the base still.
If dripping continues after these checks, contact Customer Support. If water is escaping from the tank, base or hose, stop using the appliance. Switch off and unplug it if safe. Don’t switch it back on to find the leak.
Why is my iron releasing brown water or leaving marks on clothes?
Stop ironing the garment if brown or discoloured water comes from the steam holes or the iron leaves marks. Deposits in the steam system, additives in the water, residue on the soleplate or too much heat for the fabric can all leave marks. The colour alone doesn’t tell you the cause.
- Switch off, unplug and let the iron cool. Check for residue on the soleplate and note whether discoloured water came through the steam holes.
- Check the water you’ve been using. If you’ve used scented water or additives, empty the tank once it’s cool and refill with distilled, deionised or demineralised water. If the Descale button is lit, run Self Clean as described above.
- Check the garment’s care label. Make sure the temperature was suitable. If synthetic fibres have melted onto the soleplate, follow the cleaning steps below.
For help identifying the marks, see Why is my iron leaving brown or white marks on clothes?. Follow the+- water and Self Clean instructions on this page for model 333201 and 333202.
How do I clean the ceramic soleplate?
If synthetic fibres have melted onto the soleplate, set the temperature dial to MAX and pass the iron over a clean piece of cotton to lift the deposit. Keep your hands clear of the hot soleplate. Switch off, unplug and let the iron cool afterwards.
Don’t use scouring powders or abrasive cleaning solutions. They can damage the coating. If the deposit won’t come off or the coating looks damaged, contact Customer Support.
What if my steam generator trips the electrics or smells burnt?
If the appliance trips the electrics, sparks, produces smoke or smells burnt, stop using it. Switch it off and unplug it if safe. Don’t try another socket or switch it back on to see if it happens again. Also stop using it if it has been dropped or the plug, cable or steam hose is visibly damaged.
Contact Customer Support and tell us whether it happened when you plugged it in, switched it on, started heating or used steam.
How do I switch off, clean and store my Speed Steam?
- Hold On/Off for about three seconds, unplug the appliance and let it cool.
- Remove and empty the water tank, then refit it. Wipe the cooled exterior with a damp cloth and dry it afterwards.
- Store the power lead and steam hose in loose loops in their storage slots. Avoid pulling them tight or kinking them where they meet the base.
- Slide the tip of the soleplate under the hook on the base, rest the iron in position and slide the lock to the locked padlock position. Check it’s secure before carrying the appliance by the iron handle.
Still need help with your Speed Steam 333201 or 333202?
Contact Morphy Richards UK Customer Support and include:
- The model and serial numbers from the appliance’s rating label. Let the appliance cool before checking.
- What happened and when, which lights were on or flashing, whether you heard any beeps and what you’ve already checked.
- For steam or Self Clean issues, what water you use and whether the problem started at switch-on, during ironing or during Self Clean.
- For drips, leaks or marks, where the water came from and whether it was clear or discoloured.
A photo of the controls, cooled soleplate or marks on clothing can help. Don’t switch the appliance back on to record a leak, electrical tripping, sparks, smoke or a burning smell. Describe what happened instead.