This guide covers the Morphy Richards Speed SteamPro 1.6L Steam Generator Iron (model 332102). Find out what water to use, how to control the steam and what to check if your iron won’t heat, keeps steaming after you release the trigger, or shows a descaling light.
Check the model number on the rating label underneath the base once the appliance has cooled. Use the steps below for model 332102.
Start here: what is your Speed SteamPro doing?
| What you notice | What to do first |
|---|---|
| The power light won’t come on | Check the plug, wall socket switch and On/Off button on the base. |
| The base has power but the iron won’t heat | Check that the temperature dial is above MIN and give the iron time to heat up. |
| There’s little or no steam | Check the water level, wait for the selected steam light to stay steady and make sure the iron is hot enough for steam. |
| Steam continues after you release the trigger | Steam boost may be on. Press the steam trigger once to turn boost off. |
| The iron beeps and switches off after a pause | Auto shut-off may have activated after about 10 minutes without use. Press On/Off to restart and allow the iron to heat again. |
| The descaling light is flashing | AutoClean is running. It usually takes about three minutes. Keep the tank fitted while it runs. |
| The descaling light stays on or AutoClean won’t start | Let the appliance cool completely. Fill the clean water chamber to MAX, refit the tank and switch on again. |
| Clear water drips from the soleplate | Let the iron heat fully. Use a lower steam level at a lower ironing temperature, and keep the base still. |
| Brown water comes from the soleplate or the iron leaves marks | Stop ironing the garment. Once the iron is cool, check for residue on the soleplate and check what water you’ve been using. |
| Water leaks from the base or hose, or the appliance trips the electrics, sparks, smokes or smells burnt | Stop using it. Switch off and unplug it if safe, then contact Customer Support. Don’t switch it back on to test it. |
What water should I use in my Speed SteamPro 332102?
Use 50% tap water and 50% deionised, distilled or demineralised water to help reduce limescale. For example, mix 250 ml of tap water with 250 ml of distilled water. Don’t use more than 50% deionised, distilled or demineralised water. Don’t add scented ironing water, starch, vinegar or chemical descaler.
The Speed SteamPro 332102 has a 1.6-litre water tank. When filling, use the MAX line as your guide.
- Switch off and unplug the steam generator before filling.
- Pull the detachable tank out by its handle.
- Fill the clean water chamber through the filling opening, up to the MAX line.
- Refit the tank securely.
Never fill the dirty water chamber. It collects water and limescale during AutoClean.
How do I use the steam settings and steam boost?
- Place the base on a firm, level, heat-resistant surface. Slide the iron-to-base lock to the unlocked padlock position to lift the iron off the base.
- Plug in the appliance and press On/Off on the base. The low steam light starts flashing.
- Set the temperature dial on the iron to suit the garment’s care label. Use the steam level button on the base to select Low, Medium or High.
- Wait for the selected steam light on the base to stay steady and the temperature light on the iron to go out. Hold the steam trigger for normal steam.
For steam boost, press the steam trigger twice quickly. Boost can continue after you release the trigger. Press it once more to turn boost off. If steam still won’t stop, switch off and unplug the appliance if safe, let it cool and contact Customer Support.
For dry ironing, set the temperature for the fabric and iron without using the steam trigger. You don’t need to fill the tank.
For vertical steaming, check that the garment care instructions allow it. Hold the iron about 1–2 cm from the hanging fabric and use steam boost. Turn boost off when you finish. Never steam clothes while someone is wearing them.
Why won’t my Speed SteamPro switch on or heat up?
- The power light is off: Check that the plug is fully inserted, the wall socket is switched on and you’ve pressed On/Off on the base. If there are no signs of electrical damage and you suspect the socket, check whether another appliance works in it. If the socket works but the steam generator still has no power, contact us.
- The power light is on but the iron isn’t heating: Check that the temperature dial isn’t set to MIN. Choose the setting shown on the garment’s care label and allow the iron to heat. The temperature light goes out when the selected temperature is reached. Don’t touch the soleplate to test it.
- The iron seems too hot or not hot enough: Check the temperature against the garment’s care label. If you’ve turned the dial down, wait for the iron to cool to the new setting before continuing. If it keeps scorching fabric at the correct setting or won’t heat properly, stop using it and contact us.
- It switched off after a pause: The 332102 can beep and switch off after about 10 minutes without use. Press On/Off and allow it to heat again. If it repeatedly switches off while you’re actively using steam, contact us.
Why is my Speed SteamPro producing little or no steam?
- Check the water level. If the low water light comes on, refill the clean water chamber to MAX and refit the tank securely. If the light stays on with a full, correctly fitted tank, contact us.
- Check the descaling light. If it’s flashing during AutoClean, steam won’t be available until the cycle finishes.
- Check the temperature and steam lights. Use a temperature suitable for steam and permitted by the garment’s care label. Wait for the selected steam light to stay steady and the temperature light on the iron to go out. Use dry ironing for fabrics that require a low temperature without steam.
- Use the steam trigger. Hold it for normal steam. If the iron has switched itself off after a pause, restart it and let it heat before trying again.
If steam is still weak, intermittent or absent, tell us whether it never started or worked at first and then stopped, and which lights were showing.
How do I descale my Speed SteamPro 332102?
The 332102 uses AutoClean to flush limescale from the boiler. After about 5 litres of water have been used over time, a due cycle starts when you next switch on the appliance after it has cooled completely. The 5 litres is the total water used over time, not the amount to put in the tank.
While AutoClean runs, the descaling light flashes and you won’t be able to iron. The cycle normally takes about three minutes. Keep the tank fitted while AutoClean is running: water entering the dirty water chamber is very hot.
When the cycle finishes, the descaling light goes out. The low steam light may then flash while the appliance gets ready to steam again. After ironing, switch off, unplug and let the appliance cool completely. Remove the tank and empty the dirty water chamber through its drain opening. Do this after every AutoClean cycle to prevent overflow.
Why won’t AutoClean start, or why does the descaling light stay on?
- The appliance may still be warm. Switch it off, unplug it and let it cool completely. If needed, leave it to cool overnight.
- The tank may need water or may not be fitted correctly. Fill the clean water chamber to MAX and refit the tank securely before switching on. If the low water light comes on during AutoClean, the cycle pauses. Only remove the tank once the cycle has paused and it’s safe to handle.
- The cycle may not have completed. The descaling light goes out after a successful cycle. If it stays on after the appliance has cooled and you’ve checked the tank, or the cycle repeatedly fails to finish, contact us. Don’t add descaler or vinegar to try to clear the alert.
Why is my iron dripping clear water or making a pumping noise?
An occasional pumping sound is normal while the generator moves water and maintains steam pressure.
If clear water drips from the steam holes in the soleplate, wait until the iron is hot enough for steam. Use a lower steam level at a lower ironing temperature, use shorter bursts of steam and keep the base still while ironing. If the iron has just restarted after auto shut-off, give it time to heat again.
If water keeps dripping from the soleplate after these checks, contact us. If water is leaking from the base or steam hose, stop using the appliance and don’t switch it back on to find the leak.
Why is my iron releasing brown water or leaving marks on clothes?
Stop ironing the garment if brown or discoloured water comes from the steam holes, or if the soleplate leaves marks. The colour alone doesn’t identify the cause. Deposits in the steam system, water additives, residue on the soleplate or too high a temperature for the fabric can all leave marks.
- Switch off, unplug and let the iron cool. Check the soleplate for visible residue and note whether the discoloured water came from the steam holes.
- Check what water you’ve used. If you’ve used scented water or additives, empty the clean water chamber once cool and refill it with the recommended 50/50 water mixture.
- Check the garment care label. If the mark appeared where the soleplate touched the fabric, check whether the temperature was suitable. If synthetic fibres have melted onto the soleplate, follow the cleaning steps below.
For help identifying the marks, see Why is my iron leaving brown or white marks on clothes?. Use the water and cleaning instructions on this page for model 332102. If discoloured water continues, contact us with a photo of the marks or the cooled soleplate.
How do I clean the coated soleplate?
If synthetic fibres have melted onto the soleplate, set the temperature dial to MAX and pass the iron over a clean piece of cotton to lift the residue. Keep your hands clear of the hot soleplate. Switch off, unplug and let the iron cool when you finish.
Don’t use scouring powders or abrasive cleaning solutions. They can damage the coating. If the residue won’t come off or the coating looks damaged, contact us.
What if my steam generator trips the electrics or smells burnt?
If the appliance trips the electrics, sparks, produces smoke or smells burnt, stop using it. Switch it off and unplug it if safe. Don’t try another socket or switch it back on to recreate the issue. Contact us and tell us whether it happened at plug-in, at switch-on, during heating or while steaming.
How do I switch off and store the Speed SteamPro?
Press and hold On/Off for about three seconds, then unplug the appliance and let it cool. Empty the clean water chamber and, if AutoClean has run, drain the dirty water chamber once it’s completely cool. Refit the tank.
Wipe the cooled exterior with a damp cloth and dry it afterwards. Slide the iron-to-base lock to the locked padlock position and check it’s secure before carrying the appliance by the iron handle. Store the power lead and steam hose without pulling them tight or kinking them.
Still need help with your Speed SteamPro 332102?
Contact Morphy Richards UK Customer Support and include:
- The model and serial numbers from the rating label underneath the base. Let the appliance cool before checking.
- What happens and when, including any lights or beeps and the checks you’ve already tried.
- For steam or AutoClean issues, the water mixture you use and whether the issue starts straight away or partway through ironing.
- For drips, leaks or marks, where you saw the water — the soleplate, tank, base or hose — and whether it was clear or discoloured.
A photo of the controls, cooled soleplate or marks on clothing can help. Don’t switch the appliance back on to record a leak from the base or hose, electrical tripping, sparks, smoke or a burning smell. Describe what happened instead.