This guide covers the Morphy Richards IntelliTemp SteamPro 1.6L Steam Generator Iron (model 332103). Find out what water to use, what the lights mean and what to check if your iron won’t heat, stops steaming, drips water or shows a descaling alert.
You can find your model number on the rating label on the base. Switch off, unplug and let the appliance cool before checking.
Start here: what is your IntelliTemp SteamPro doing?
| What you notice | What to do first |
|---|---|
| The power light won’t come on | Check that the plug is fully inserted, the socket is switched on and you’ve pressed On/Off on the base. |
| The base has power but the iron won’t heat | Give the iron time to warm up. On the 332103, the temperature light on the iron comes on when it’s ready. |
| The iron heats up but produces little or no steam | Check the clean water level and wait for the selected steam light on the base to stop flashing. Then hold the steam trigger. |
| Steam continues after you release the trigger | Steam boost may be on. Press the steam trigger once to turn it off. |
| The iron beeps and switches off after a pause | Auto shut-off may have activated after about 10 minutes without use. Press On/Off and let the iron heat again. |
| The descaling light is flashing | AutoClean is running. It normally takes about three minutes. Keep the tank fitted while the cycle runs. |
| The descaling light stays on or AutoClean won’t start | Let the appliance cool completely. Fill the clean water chamber to MAX, refit the tank securely and switch on again. |
| A few clear drops come from the soleplate | Let the iron heat fully, use shorter bursts of steam and keep the base still. |
| Brown water comes from the soleplate or the iron leaves marks | Stop ironing the garment. Once the iron is cool, check the soleplate for residue and check what water you’ve been using. |
| Water leaks from the tank, base or hose, or the appliance trips the electrics, sparks, smokes or smells burnt | Stop using it. Switch off and unplug it if safe, then contact Customer Support. Don’t switch it back on to test it. |
What water should I use in my IntelliTemp SteamPro 332103?
Use 50% tap water and 50% deionised, distilled or demineralised water to help reduce limescale. For example, mix 250 ml of tap water with 250 ml of distilled water. Don’t use more than 50% deionised, distilled or demineralised water, even in a hard water area.
Don’t add scented ironing water, starch, vinegar, chemical descaler or other additives.
The 332103 has a 1.6-litre water tank. Use the MAX line when filling:
- Switch off and unplug the steam generator.
- Pull the detachable tank out by its handle.
- Fill the clean water chamber through the filling opening, up to the MAX line.
- Refit the tank securely.
Never fill the dirty water chamber. It collects water and limescale during AutoClean.
How do I use IntelliTemp and choose the steam level?
IntelliTemp uses one temperature setting for ironable fabrics. You don’t need to adjust the temperature between garments. Check each garment’s care label and never iron anything marked Do not iron. If the label advises against steam, iron without steam.
- Place the base on a firm, level, heat-resistant surface. Slide the iron-to-base lock to the unlocked padlock position and lift the iron off the base.
- Plug in the appliance and press On/Off on the base. The low steam light starts flashing.
- Press the steam level button on the base to cycle through Low → Medium → High → Low.
- Wait for the temperature light on the iron to come on and the selected steam light on the base to stay steady.
- Press and hold the steam trigger for normal steam. Release it to stop.
The steam level changes how much steam the iron produces. It does not change the IntelliTemp temperature setting.
How do I use steam boost, and why won’t the steam stop?
Press the steam trigger twice quickly to turn on steam boost. Boost can continue after you release the trigger. Press the trigger once more to turn it off.
If steam continues after you’ve turned boost off, switch off and unplug the appliance if safe. Let it cool and contact Customer Support.
Can I iron without steam or steam clothes on a hanger?
- Dry ironing: You don’t need to fill the tank or select a steam level. Let the iron heat up and iron without holding the steam trigger. If it switches off after about 10 minutes, press On/Off and let it heat again.
- Vertical steaming: If the garment’s care instructions allow steam, hold the iron about 1–2 cm from the hanging fabric. Press the trigger twice quickly for boost, then once to stop it. Never steam clothes while someone is wearing them.
Why won’t my IntelliTemp SteamPro switch on or heat up?
- No power light: Check the plug, socket switch and On/Off button on the base. If the socket shows no signs of damage and hasn’t tripped, check whether another appliance works in it. If the socket works but the steam generator still has no power, contact us.
- The power light is on but the iron isn’t heating: Allow a minute or two for the iron to reach temperature after switching it on or restarting it. The temperature light on the iron comes on when it’s ready. Don’t touch the soleplate to check whether it’s hot. If the iron still doesn’t heat, contact us.
- The iron seems too hot or not hot enough: Check the garment’s care label and allow the iron time to reach its operating temperature. If it repeatedly scorches ironable fabrics or doesn’t heat properly after warming up, stop using it and contact us.
- The iron switched off after a pause: The 332103 beeps and switches off after about 10 minutes without use. Press On/Off and let it heat again. If it repeatedly switches off while you’re actively using steam, contact us.
Why is my IntelliTemp SteamPro producing little or no steam?
- Check the clean water level. If the low water light is on, refill to MAX and refit the tank securely. If the light stays on with a full, correctly fitted tank, contact us.
- Check whether AutoClean is running. If the descaling light is flashing, wait for the cycle to finish.
- Wait for both ready lights. The temperature light on the iron should be on and the selected steam light on the base should be steady. If the iron has just restarted after auto shut-off, let it heat again.
- Hold the steam trigger. For more steam, select a higher steam level if the fabric allows it and wait for the new steam light to stay steady.
If steam is still weak, intermittent or absent, tell us whether it never started or worked at first and then stopped, and which lights were showing.
How do I descale my IntelliTemp SteamPro 332103?
The 332103 uses AutoClean to flush limescale from the boiler. A cycle is due after the appliance has used about 5 litres of water over time. It starts automatically the next time you switch on the appliance after it has cooled completely. The 5 litres is the amount used between cycles; fill the tank only to its MAX line.
- Before switching on, make sure the clean water chamber is filled and the tank is fitted securely.
- When AutoClean runs, the descaling light flashes and you can’t iron. The cycle normally takes about three minutes. Do not remove the tank while AutoClean is running. The water going into the dirty water chamber is very hot.
- The descaling light goes out when the cycle finishes. The low steam light may flash while the appliance gets ready to steam again.
- After ironing, switch off, unplug and let the appliance cool completely. Remove the tank and empty the dirty water chamber through its drain opening. Empty it after every completed AutoClean cycle to prevent overflow.
Why won’t AutoClean start, or why does the descaling light stay on?
- The appliance may still be warm. Switch off, unplug and let it cool completely. If needed, leave it to cool overnight. Fill the clean water chamber to MAX and refit the tank securely before switching on again.
- The low water light is on during AutoClean. The cycle pauses if there isn’t enough water. Wait until it has paused and the tank is safe to handle before refilling and refitting it. Do not remove the tank while water is being discharged.
- The cycle hasn’t finished. The descaling light goes out after a successful cycle. If it stays on after you’ve checked the water and let the appliance cool, or the cycle won’t finish, contact us.
AutoClean starts when it’s due. Don’t add vinegar or chemical descaler to try to start the cycle or clear the light.
Why is my iron dripping clear water or making a pumping sound?
An occasional pumping sound is normal. It’s the sound of water moving through the steam generator.
If a few clear drops come from the steam holes in the soleplate, wait until the iron’s temperature light is on and the selected steam light on the base is steady. Use shorter bursts of steam, keep the base still and check that you’re using the 50/50 water mixture. If the iron has just restarted after auto shut-off, give it time to heat again.
If dripping continues once the iron is ready, contact us. If water is escaping from the tank, base or hose, stop using the appliance. Switch off and unplug it if safe. Don’t switch it back on to find the leak.
Why is my iron releasing brown water or leaving marks on clothes?
Stop ironing the garment if brown or discoloured water comes from the steam holes, or if the iron leaves marks. The colour alone doesn’t tell you the cause. Deposits in the steam system, additives in the water or residue on the soleplate can all leave marks.
- Switch off, unplug and let the iron cool. Check the soleplate for visible residue. Note whether discoloured water came from the steam holes or whether the marks appeared where the soleplate touched the fabric.
- Check what water you’ve used. If you’ve used scented water or additives, empty the clean water chamber once cool and refill it with 50% tap water and 50% deionised, distilled or demineralised water. Don’t add a cleaning product to the tank.
- Check the garment’s care label. If synthetic fibres have melted onto the soleplate, follow the cleaning steps below.
For help identifying the marks, see Why is my iron leaving brown or white marks on clothes?. Use the water and cleaning steps on this page for model 332103. If discoloured water continues, contact us. A photo of the marks or the cooled soleplate can help.
How do I clean the ceramic soleplate?
If synthetic fibres have melted onto the soleplate, pass the heated iron over a clean piece of cotton to lift the deposit. Keep the iron moving and your hands clear of the soleplate. Switch off, unplug and let the iron cool when you finish.
Don’t use scouring powders or abrasive cleaning solutions. They can damage the ceramic coating. If the deposit won’t come off or the coating looks damaged, contact us.
What if the iron trips the electrics, sparks or smells burnt?
Stop using it. Switch off and unplug it if safe. Don’t try another socket or switch it back on to see if it happens again. If the appliance has been dropped or the plug, cable or steam hose is visibly damaged, stop using it and contact us.
Contact Morphy Richards UK Customer Support and tell us whether it happened when you plugged it in, switched it on, started steaming or were already ironing.
How do I switch off, clean and store my IntelliTemp SteamPro?
- Hold On/Off for about three seconds, then unplug the appliance and let it cool.
- Empty the clean water chamber. If AutoClean has run, drain the dirty water chamber once the appliance is completely cool. Refit the tank.
- Wipe the cooled exterior with a damp cloth and dry it afterwards.
- Slide the tip of the soleplate under the hook on the base, rest the iron in position and slide the lock to the locked padlock position. Check that it’s secure before carrying the appliance by the iron handle.
- Loop the power lead and steam hose loosely and tuck them into the storage areas on either side of the base. Avoid pulling them tight or kinking them.
Still need help with your IntelliTemp SteamPro 332103?
Contact Morphy Richards UK Customer Support and include:
- The model and serial numbers from the rating label on the base. Let the appliance cool before checking.
- What happens and when, including which lights are on or flashing, whether you hear a beep and what you’ve already checked.
- For steam or AutoClean issues, the water mixture you use and whether the issue starts straight away or partway through ironing.
- For drips, leaks or marks, where you saw the water — the soleplate, tank, base or hose — and whether it was clear or discoloured.
A photo of the controls, cooled soleplate or marks on clothing can help. Don’t switch the appliance back on to record a leak, electrical tripping, sparks, smoke or a burning smell. Describe what happened instead.