This guide covers the Morphy Richards Power SteamElite Steam Generator Iron, model 332014. Find out what water to use, how AutoClean works and what to check if your iron stops steaming, spits water or leaves marks on clothes.
Start here: what is your Power SteamElite doing?
| What you notice | What to do first |
|---|---|
| The power light doesn’t come on | Check that the plug is fully inserted, the wall socket is switched on and you’ve pressed On/Off on the base. |
| The base has power but the iron isn’t heating | Check the temperature dial on the iron and allow it time to reach the selected setting. Don’t touch the soleplate to check it. |
| The iron heats up but produces little or no steam | Check the clean water level. Wait for the steam light on the base to stay steady and the temperature light on the iron to go out. Then hold the steam trigger. |
| Steam stops, the appliance beeps and the low water light comes on | Refill the clean water chamber and refit the tank securely. If AutoClean is running, wait for it to pause before handling the tank. |
| The descaling light flashes when you switch on | AutoClean is running. It normally takes about three minutes. Keep the tank fitted while the cycle runs. |
| The soleplate spits a few clear droplets | Let the iron reach the selected temperature, use shorter bursts of steam and keep the base still. |
| Brown water comes from the steam holes or the iron leaves marks | Stop ironing the garment. Once the iron has cooled, check for residue on the soleplate and check what water you’ve been using. |
| Synthetic fabric is stuck to the soleplate | Follow the coated soleplate cleaning steps below. Avoid scouring powders and abrasive cleaners. |
| Water leaks from the base or hose, the appliance trips the electrics, or you notice smoke, sparks, a burning smell or visible damage | Stop using it. Switch off and unplug it if safe, then contact Customer Support. Don’t switch it back on to test it. |
What water should I use, and how much should I add?
Use 50% tap water and 50% deionised, distilled or demineralised water to help reduce limescale. For example, mix 250 ml of tap water with 250 ml of distilled water. Don’t use more than 50% deionised, distilled or demineralised water. Don’t add scented ironing water, vinegar, chemical descaler, starch or other additives.
- Switch off and unplug the steam generator before filling.
- Remove the detachable tank and open the filling cap.
- Fill the clean water chamber up to the MAX line.
- Close the cap and refit the tank securely.
Leave the dirty water chamber empty. It collects water and limescale during AutoClean.
How do I use the steam settings?
- Place the base on a firm, level, heat-resistant surface. To unlock the iron, use the release button marked with a padlock.
- Plug in the appliance and press On/Off on the base. The power light comes on and the low steam light starts flashing.
- Set the temperature dial on the iron to suit the garment’s care label. Use the steam level buttons on the base to choose Low, Medium or High.
- Wait until the selected steam light on the base stays on steadily and the temperature light on the iron goes out.
- Press and hold the steam trigger for a continuous flow of steam.
The temperature dial controls how hot the soleplate gets. The steam level buttons control how much steam the appliance produces. If you turn the temperature down for a more delicate fabric, wait for the iron to reach the new setting before continuing.
For dry ironing, set the temperature for the fabric and iron without using the steam trigger. You don’t need to fill the tank.
For vertical steaming, check that the garment’s care instructions allow it. Hold the iron about 1–2 cm from the hanging fabric and use the steam trigger. Never steam clothes while someone is wearing them.
Why won’t my Power SteamElite 332014 switch on or heat up?
- The power light is off: Check that the plug is fully inserted, the socket is switched on and you’ve pressed On/Off on the base. If the light still doesn’t come on, contact Customer Support.
- The power light is on but the iron doesn’t heat: Set the temperature dial to suit the fabric and give the iron time to heat up. The temperature light goes out when the selected temperature is reached. If the iron still isn’t heating, contact Customer Support. Don’t touch the soleplate to test it.
- The appliance switched off after a pause: Press On/Off and wait for it to heat again. If it repeatedly switches off while you’re actively using steam, contact us and tell us when it stops, which lights are showing and whether it beeps.
Why is my steam generator producing little or no steam?
- Check the water level and tank fitting. If the low water light comes on and the appliance beeps, steam stops. Refill the clean water chamber and refit the tank securely. If the low water light stays on with a full, correctly fitted tank, contact Customer Support.
- Check whether AutoClean is running. A flashing descaling light means the cleaning cycle is in progress. Wait for it to finish.
- Wait for the iron and steam generator to be ready. The selected steam light on the base should be steady and the temperature light on the iron should be off.
- Hold the steam trigger. If you need more steam, choose a higher steam level if the garment’s care instructions allow it. Wait for the new steam light to stay steady before continuing.
If steam is still weak, intermittent or absent, tell Customer Support whether it never started or worked at first and then stopped. Include any lights or beeps you noticed.
How do I descale my Power SteamElite 332014?
The 332014 uses AutoClean to flush limescale from the boiler. After the appliance has used about 5 litres of water in total, AutoClean starts the next time you switch it on after it has cooled completely. The 5 litres is the amount used over time; fill the tank only to its MAX line.
- Make sure there is water in the clean water chamber before switching on.
- If AutoClean is due, the descaling light flashes and you won’t be able to iron. The cycle normally takes about three minutes. Keep the tank fitted while AutoClean is running. Water entering the dirty water chamber is very hot.
- When the descaling light goes out, AutoClean has finished. The low steam light may flash while the appliance gets ready to steam again.
- After ironing, switch off, unplug and let the appliance cool completely. Remove the tank and empty the dirty water chamber through its drain holes. Empty it after every AutoClean cycle to prevent overflow.
Can I start AutoClean manually?
AutoClean runs automatically when it’s due. Switching on a fully cooled appliance lets a due cycle start. You don’t need to add descaler or repeatedly switch the appliance off and on to try to start it.
Why is the descaling light still flashing?
Check whether the low water light is also on. If there isn’t enough clean water, AutoClean pauses. Once the cycle has paused and the tank is safe to handle, refill the clean water chamber and refit the tank so the cycle can continue.
If the descaling light keeps flashing well beyond the usual three minutes, or the cycle won’t resume after the tank has been refilled and refitted, contact Customer Support. Tell us which lights are on or flashing and whether you heard a beep.
Why is my steam generator spitting water or making a pumping noise?
An occasional pumping sound is normal. It’s the sound of water moving through the steam generator.
A few clear droplets from the soleplate can occur during steaming. To reduce them, wait until the iron has reached the selected temperature, use shorter bursts of steam and keep the base still while ironing.
If the soleplate keeps releasing water after the iron is ready, contact Customer Support. If water is leaking from the base or steam hose, stop using the appliance. Switch it off and unplug it if safe. Don’t switch it back on to check where the leak is coming from.
Why is my iron releasing brown water or leaving marks on clothes?
If brown or discoloured water comes from the steam holes, or the iron leaves marks on clothing, stop ironing the garment. Possible causes include deposits in the steam system, additives in the water, residue on the soleplate or a temperature setting that is too high for the fabric. The colour alone doesn’t tell you what caused it.
- Switch off, unplug and let the iron cool. Look for visible residue on the soleplate and note whether the discoloured water came from the steam holes.
- Check the water you’ve been using. If you’ve used scented water or additives, empty the clean water chamber once the appliance is cool. Refill with 50% tap water and 50% deionised, distilled or demineralised water.
- Check the garment’s care label. If the mark appeared where the soleplate touched the fabric, check whether the temperature was suitable. If synthetic fibres are stuck to the soleplate, follow the cleaning steps below.
For help identifying the marks, see Why is my iron leaving brown or white marks on clothes?. Follow the water and cleaning instructions on this page for model 332014.
How do I clean the coated soleplate?
If synthetic fibres have melted onto the soleplate, set the iron’s temperature dial to MAX and pass the iron over a clean piece of cotton to lift the residue. Keep the iron moving and your hands clear of the hot soleplate. When finished, switch off, unplug and let the iron cool.
Don’t use scouring powders or abrasive cleaning solutions. They can damage the coating. If the residue won’t come off or the coating looks damaged, contact Customer Support.
What if my steam generator trips the electrics or smells burnt?
If it trips the electrics, sparks, produces smoke or smells burnt, stop using it. Switch it off and unplug it if safe. Don’t try another socket or switch it back on to recreate the issue.
Contact Morphy Richards UK Customer Support and tell us whether it happened when you plugged it in, switched it on, started steaming or were already ironing.
How do I clean and store the steam generator after use?
- Press and hold On/Off for about three seconds, unplug the appliance and let it cool.
- Empty any remaining clean water. If AutoClean has run, drain the dirty water chamber once the appliance is completely cool. Refit the tank.
- Wipe the cooled exterior with a damp cloth and dry it afterwards.
- Lock the iron onto the base before lifting it by the iron handle. Wrap the power lead and steam hose loosely in the storage groove to avoid pulling or kinking them.
Still need help with your Power SteamElite 332014?
Contact Morphy Richards UK Customer Support and include:
- The model and serial numbers from the rating label underneath the base. Let the appliance cool before checking.
- What happens and when, such as at switch-on, while ironing or during AutoClean.
- Which lights are on or flashing, whether you hear a beep and which checks you’ve already tried.
- For steam or descaling issues, the water mixture you use. For water or marks, tell us whether the water came from the soleplate, tank, base or hose, and what colour it was.
A photo of the controls, cooled soleplate or marks on clothing may help. A short video can also be useful if it’s safe to take one. If the appliance has leaked from the base or hose, tripped the electrics, sparked, smoked or smelled burnt, don’t switch it back on to take a photo or video. Describe what happened instead.