The Morphy Richards SteamElite Plus Steam Generator (model 332013) features an automatic cleaning system (Auto Clean) designed to remove limescale from the boiler and help maintain consistent steam performance.
If your descaling indicator light is flashing, your steam generator may be carrying out its automatic cleaning cycle.
This guide explains how Auto Clean works, how to empty the dirty water chamber, which water to use and what to do if the descaling indicator won't go out or steam performance has decreased.
Applies to: Morphy Richards Power SteamElite Plus Steam Generator, model 332013.
How Does the Auto Clean Function Work?
The SteamElite Plus automatically performs a cleaning cycle after approximately 5 litres of water have been used.
When cleaning is due, the appliance will begin Auto Clean when it has cooled completely and is next switched on.
During the cycle:
- The descaling indicator light flashes.
- Water is drawn from the clean water chamber and pumped through the boiler.
- Limescale particles and dirty water are flushed into the dirty water chamber.
- Steam ironing is temporarily unavailable.
- The cleaning process takes approximately 3 minutes.
Once Auto Clean is complete, the descaling indicator light goes out and the appliance begins preparing for normal steam operation.
Important: Auto Clean is an automatic function. There is no separate button to manually activate the descaling cycle.
Step 1: Allow the Steam Generator to Cool
The appliance must have cooled completely before an automatic cleaning cycle can begin.
- After ironing, press and hold the On/Off button for approximately 3 seconds to switch off the appliance.
- Unplug the steam generator from the mains.
- Allow the appliance to cool completely.
- When you're ready to use it again, place it on a stable, heat-resistant surface and switch it on.
If Auto Clean is due, the cleaning process will begin automatically.
Do not attempt to force the cleaning cycle by repeatedly switching the appliance on and off.
Step 2: Check and Fill the Water Tank
Auto Clean requires sufficient water to flush the boiler.
- Check that the detachable water tank contains enough water.
- If necessary, remove the tank using the water tank release button.
- Open the filling cap.
- Fill the clean water chamber with the recommended water mixture, without exceeding the maximum filling level.
- Close the filling cap securely.
- Refit the water tank, ensuring it is correctly positioned.
What Water Should I Use?
For this model, Morphy Richards recommends a mixture of:
- 50% tap water
- 50% deionised, distilled or demineralised water
Do not use more than 50% deionised, distilled or demineralised water.
Do not use:
- Scented ironing water or fragranced water
- Water containing perfumes or other additives
- Chemical descaling solutions
- Vinegar or other household cleaning products
These substances are not suitable for the appliance and may affect its performance or internal components.
Important: Only fill the clean water chamber through the designated filling cap. Never pour water directly into the dirty water chamber.
Step 3: Allow the Auto Clean Cycle to Complete
When Auto Clean starts, the descaling indicator light will flash while the appliance flushes its boiler.
The process takes approximately 3 minutes.
During this time:
- Do not attempt to use the iron for steam ironing.
- Do not remove the water tank while the cleaning cycle is operating.
- Do not interrupt the cycle unnecessarily.
- Keep children and pets away from the appliance.
Warning: Water transferred into the dirty water chamber during Auto Clean will be very hot.
What Happens if the Water Tank Runs Low?
If there isn't enough water to complete the cleaning cycle:
- The low water level indicator will illuminate.
- Auto Clean will pause.
- Refill the clean water chamber with the recommended water mixture.
- Refit the water tank securely.
The cleaning process can then continue.
Once Auto Clean has finished, the descaling indicator light will go out. The appliance will then begin preparing for normal steam operation.
Step 4: Empty the Dirty Water Chamber
After every Auto Clean cycle, it's important to empty the dirty water chamber to prevent it from overflowing during future cleaning cycles.
The dirty water chamber is incorporated into the detachable water tank. It is not a separate container that needs to be dismantled.
Always allow the appliance to cool completely before emptying the dirty water.
- Once you've finished using the steam generator, switch it off.
- Unplug the appliance from the mains.
- Allow it to cool completely.
- Press the water tank release button and carefully remove the detachable water tank.
- Hold the tank over a sink.
- Carefully tip out the collected dirty water through the designated dirty water emptying holes.
- Ensure the dirty water chamber is fully emptied.
- Refit the water tank securely.
The water may contain small particles of limescale or other mineral deposits removed during the cleaning process.
Important: Do not attempt to open, dismantle or manually clean the internal boiler. The Auto Clean system is designed to manage boiler cleaning automatically.
Why Is My Descaling Indicator Light Flashing?
A flashing descaling indicator usually means that Auto Clean is in progress.
| What you're experiencing | What to do |
|---|---|
| Descaling light flashes when the appliance is switched on | Allow Auto Clean to complete. This normally takes approximately 3 minutes. |
| The appliance won't produce steam while the descaling light flashes | Steam ironing is temporarily unavailable during Auto Clean. Wait for the cycle to finish. |
| The low water indicator illuminates during Auto Clean | Refill the clean water chamber and securely refit the tank. |
| The descaling light goes out after cleaning | Auto Clean has finished. Allow the appliance to prepare for normal steam operation. |
| The descaling light continues flashing and the cycle doesn't finish | Check the water level and tank fitment. If the issue continues, further assessment may be required. |
Can I Manually Start the Auto Clean Cycle?
No. The SteamElite Plus 332013 automatically determines when its boiler needs cleaning.
The cycle is triggered after approximately 5 litres of water have been used and runs when the appliance has cooled completely and is next switched on.
There is no separate manual descaling button, and you should not add descaling chemicals to the water tank.
If your appliance is producing less steam than usual between Auto Clean cycles, follow the troubleshooting steps below.
Why Is My Steam Generator Still Producing Less Steam After Auto Clean?
Auto Clean removes limescale from the boiler, but reduced or interrupted steam production can have several possible causes.
Before contacting Customer Support, please check the following:
1. Check the Water Level
If the water level is too low, the low water indicator will illuminate, the appliance will beep and steam production will stop.
Remove the water tank, refill the clean water chamber with the recommended water mixture and refit the tank securely.
2. Allow the Appliance to Reach the Correct Temperature
The selected steam level indicator will flash while the appliance is preparing to produce steam.
Wait until the indicator remains steadily illuminated before using the steam trigger.
Also ensure the iron's temperature indicator light has gone out, indicating that the soleplate has reached the selected temperature.
3. Use the Steam Controls Correctly
The SteamElite Plus provides continuous steam through the steam trigger and a separate steam boost function.
Do not press the steam boost button and continuous steam trigger at the same time.
Using both controls together can interrupt the steam flow and may cause continuous steam to stop completely.
For a consistent flow of steam, select the appropriate steam level and use the continuous steam trigger.
4. Check Whether the Appliance Has Automatically Switched Off
The SteamElite Plus has an automatic shut-off feature.
If neither the steam trigger nor the steam boost button has been used for approximately 10 minutes, the appliance will switch off automatically.
To restart it, press the On/Off button and allow the appliance to reach its operating temperature again.
5. Check for Water Droplets or Pumping Noises
Occasional pumping sounds during steam ironing are normal. They occur as water is pumped through the steam generator.
Small amounts of water may also be released from the soleplate, particularly if the iron hasn't reached the correct temperature.
Allow the iron to heat fully before steaming and avoid moving the steam generator base during use.
6. Consider Previous Water Usage
Using unsuitable water or water containing additives may contribute to mineral deposits, residue or reduced steam performance.
For this model, use the recommended mixture of 50% tap water and 50% deionised, distilled or demineralised water.
Do not add chemical descalers, vinegar, scented water or ironing additives to the water tank.
If steam production remains weak, inconsistent or completely absent after completing these checks, further assessment may be required.
How Can I Prevent Limescale Build-Up?
To help maintain your SteamElite Plus and reduce the likelihood of limescale-related problems:
- Use the recommended water mixture: 50% tap water and 50% deionised, distilled or demineralised water.
- Avoid scented or treated ironing water: Do not add fragrances, cleaning agents or descaling chemicals to the tank.
- Allow Auto Clean to finish: When the descaling indicator flashes, let the automatic cleaning process complete.
- Empty the dirty water chamber: Always empty it after Auto Clean, once the appliance has cooled completely.
- Keep the water tank clean: Check for visible residue and follow the normal care instructions.
- Pay attention to changes in steam performance: Reduced steam, unusual discharge or persistent indicator lights may require further troubleshooting.
Regular maintenance helps keep the appliance operating effectively and reduces the risk of mineral deposits affecting steam performance.
What Should I Do if the Descaling Light Won't Go Out?
If the descaling indicator continues flashing beyond the normal cleaning period:
- Check whether the low water level indicator is illuminated.
- Refill the clean water chamber if necessary, using the recommended water mixture.
- Ensure the detachable water tank is fitted securely.
- Allow the automatic cleaning process to continue without interruption.
- Once the cycle has completed and the appliance has cooled, empty the dirty water chamber.
If Auto Clean repeatedly fails to finish, the descaling indicator remains illuminated or the appliance is still unable to produce steam, stop using it and contact Customer Support.
Still Need Help?
If you've followed the troubleshooting steps above and your Morphy Richards SteamElite Plus (332013) is still experiencing problems, please contact Morphy Richards Customer Support.
To help us assess the issue and advise on the appropriate next steps, please provide all of the following information when contacting us:
- Serial number: This is located on the appliance's rating label. Please provide the serial number or a clear photograph of the rating label. Switch off, unplug and allow the appliance to cool before locating the label.
- Video demonstrating the issue: Please provide a short, clear video showing what the appliance is or isn't doing, including any flashing indicator lights, error messages or problems with steam production. Only record the appliance where it is safe to do so. Do not attempt to reproduce an unsafe fault.
- Postcode: Please confirm your full UK postcode.
- Water type used: Please confirm whether you've been using tap water, distilled, deionised or demineralised water, a mixture of these, or any other type of water. If using a mixture, please specify the approximate proportions.
- Troubleshooting completed: Please confirm which steps you've already followed and what happened.
Providing this information will help our Customer Support team assess your enquiry and determine the appropriate next steps as quickly as possible.
You can also download the Morphy Richards SteamElite Plus 332013 instruction manual for further product information.