EasyCharge Cordless Steam Irons – Models 303250, 303251 and 303252
If your Morphy Richards EasyCharge cordless steam iron causes your electrics to trip, a fuse to blow or a circuit breaker to switch off, this may indicate a problem with the electrical supply, an overloaded circuit or the appliance itself.
If your iron has caused the electrics to trip, stop using it and unplug it if safe to do so. Do not repeatedly reset the electrics and try the iron again.
The information below explains possible causes, the checks you can safely make and when to contact Customer Support.
Why Is My Cordless Iron Tripping the Electrics?
There are several possible reasons why your iron may cause a fuse, circuit breaker or RCD (residual current device) to trip.
1. Too Many Appliances on the Same Circuit
Irons are high-powered electrical appliances.
If other high-wattage appliances, such as kettles, heaters or tumble dryers, are operating on the same circuit, the combined electrical demand may exceed the circuit's capacity.
This can cause a circuit breaker to trip as a protective measure.
What should I do?
- Check whether several high-powered appliances were operating when the electrics tripped.
- Avoid connecting multiple high-wattage appliances through an extension lead or multi-plug adaptor.
- Disconnect the iron and leave it unused while the cause is investigated.
An overloaded circuit is one possible explanation, but it should not be assumed to be the cause without further checks.
2. A Problem with the Wall Socket or Electrical Supply
A damaged socket, loose electrical connection or wiring problem may cause protective devices to operate.
What should I check?
With the appliance disconnected, look for obvious signs of damage to the socket, such as:
- Cracks or discolouration.
- Scorch marks or signs of overheating.
- A burning smell.
- Loose or damaged fittings.
Do not use a socket that appears damaged or has been overheating. Arrange for it to be checked by a qualified electrician.
If the electrics continue to trip even when the iron is disconnected, this may indicate a problem elsewhere in the electrical installation.
3. A Blown or Incorrect Plug Fuse
Your cordless iron is fitted with a fused UK mains plug.
The existing product guidance specifies a 13A BS1362 fuse.
If the plug fuse has blown, the iron may stop receiving power.
Important: A blown fuse does not necessarily mean the fuse itself was the original problem.
If the appliance caused an electrical trip or a fuse has blown unexpectedly, do not simply replace the fuse and repeatedly attempt to use the iron. The underlying cause may need investigation.
Never bypass a fuse or fit one with an incorrect rating.
4. A Damaged Plug or Power Cable
Damage to the plug or mains cable can create an electrical hazard.
With the appliance unplugged, visually check for:
- Fraying, cuts or exposed wires.
- A crushed or damaged cable.
- Bent or damaged plug pins.
- Signs of burning, melting or overheating.
If you notice any damage, do not reconnect or use the appliance.
Do not attempt to repair the cable, plug or internal electrical components yourself.
5. A Possible Internal Electrical Fault
If the electrical supply appears normal and the iron has caused a circuit breaker or RCD to trip, a fault within the appliance or its powered base is another possible cause.
This cannot be confirmed from the tripping alone.
An internal electrical issue requires appropriate assessment rather than repeated testing by the customer.
Do not dismantle the iron or powered base to investigate.
What Should I Do If My Iron Trips the Electrics?
Follow these safety steps:
- Stop using the iron immediately.
- Switch off the mains socket and unplug the appliance, provided it is safe to do so.
- Do not reconnect the iron to another socket simply to see whether it trips again.
- Visually inspect the unplugged appliance, plug and cable for obvious damage. Do not touch exposed wiring or damaged electrical parts.
- Consider whether several high-powered appliances were operating on the same circuit when the trip occurred.
- If the electrical installation continues to trip without the iron connected, seek advice from a qualified electrician.
- Contact Morphy Richards Customer Support if the iron appears to have caused the trip.
Do not continue using the appliance until the cause has been appropriately assessed.
Should I Try My Iron in Another Socket?
The product troubleshooting guidance identifies trying another socket as a possible way to distinguish supply problems from appliance problems.
However, if your iron has already caused a fuse, circuit breaker or RCD to trip, we do not recommend repeatedly reconnecting it to different sockets.
A tripping electrical safety device may be responding to a genuine fault.
The safest approach is to stop using the iron and arrange an appropriate assessment.
If your iron simply has no power and has not caused any electrical tripping, please follow our separate guide:
Why Is My Morphy Richards Cordless Steam Iron Not Heating?
Could Water Cause My Iron to Trip the Electrics?
Water entering electrical components can create an electrical hazard.
If your iron has been dropped into water, exposed to a significant spill or is leaking near the electrical connectors or powered base:
- Stop using it immediately.
- Disconnect it from the mains if safe to do so.
- Do not attempt to operate it again to check whether it has dried out.
- Do not dismantle the appliance or attempt an internal repair.
Contact Customer Support for advice.
Do not use the self-cleaning function or carry out steam troubleshooting on an appliance suspected of having an electrical fault.
Is Electrical Tripping a Manufacturing Fault?
Not necessarily.
Electrical tripping can be caused by the household electrical supply, circuit overload, a damaged socket or a problem with the appliance.
The fact that a circuit breaker or RCD has operated does not, by itself, establish which of these is responsible.
If the information provided suggests a possible appliance fault, our Customer Support team can advise whether further investigation or a warranty assessment is appropriate.
Still Need Help?
If your Morphy Richards cordless iron has caused your electrics to trip, please contact Morphy Richards Customer Support.
To help us assess your enquiry, please provide:
- Model number: 303250, 303251 or 303252.
- Serial number: Where available, or a photograph of the product rating label.
- Proof of purchase: Showing the retailer, purchase date and product.
- What happened: Explain whether a plug fuse blew, a circuit breaker switched off or an RCD tripped.
- When it happened: For example, immediately when switching on, while heating on the base or during ironing.
- Other appliances: Confirm whether other high-powered appliances were being used on the same circuit.
- Visible damage: Let us know whether the plug, cable, base or iron shows any signs of damage, overheating or water ingress.
- Photographs: Where safe, provide clear images of any visible damage. Do not reconnect the appliance to obtain photographs or video evidence.
Our team will review the information and advise whether further investigation or a warranty assessment is required.
Please do not reconnect, test or return the appliance unless instructed to do so following an appropriate safety assessment.
For other product questions, visit our EasyCharge Cordless Iron Troubleshooting & Support Hub.